Use machine edge medium speed grinder use machine

Use machine edge medium speed grinder use machine

Can be used for all kinds of plastic materials crushing the re-use, including plastic scrap, back to the material, semi-finished products for soft chlorine, polycarbonate, nylon, ABS and other hard and soft type of plastic, Mesh plastic. The machine is compact, handsome in appearance, easy to operate, turn the knife to optimize the design to minimize energy consumption, higher cutting efficiency. Time: 30 seconds immediately recovery, do not have to wait for the concentration of crushing, and indeed clean, clean; improve quality: outlet material in the high temperature will be exposed to oxidation, moisture (absorb moisture) and damage physical properties, 30 seconds immediately Reduce the physical strength, reduce the loss of color luster; save money: short-term recovery, to avoid pollution, mixing caused by the non-performing rate, can reduce the plastic, labor, management, storage, purchase capital waste and loss; Suitable for crushing and recycling of PU, PVC, PC, ABC and other soft and hard material outlet material; simple: easy to split design, color change material easy and easy, small and less space, suitable for small workshop next to the use of the machine; Low noise, low energy consumption; the use of stainless steel into the hopper design, easy to clean, do not pollute the raw materials; motor with overload protection device, and a power supply chain protection system, safe and reliable operation; optional automatic recovery system or powder separation system, Fully avoid the waste of human resources, so as to achieve the best recovery effect.

Use machine edge medium speed grinder use machine

The advantages of the machine side of the speed of the crusher equipped with motor overload and power supply chain and safety switches and other protection systems, and equipped with card alarm system, easy to operate safe and hopper type and automatic recycling options. Hopper type, the machine comes with the bottom of the hopper, loading crushed after the completion of the material; automatic recovery type, the machine has a matching recovery system, you can crush the material directly into the injection molding machine to continue recycling. The advantages and disadvantages of the powerful pulverizer: the shaft speed is fast, the impact of crushing with the cutting tool cutting, for most of the plastic, rubber, Chinese herbal medicine, wood products, etc. have a good Smashing effect. And the grinding power from small to large selection range, minicomputer can be used for machine edge smash and install the immediate recovery device, saving manpower and material and turnaround time. Mainframe can achieve centralized crushing, high yield, can also be configured large-scale recovery bagging fan, smash at the same time, the crushed material blowing through the fan to the storage bucket. Compared with the slow crusher, strong crusher noise, crushed after the particles as slow crusher evenly. Slow mute the advantages and disadvantages: slow speed, teeth bite-type crushing, uniform particles, no screen, easy cleaning and disassembly can be configured immediately recovery device to achieve the proportion of crushed material and raw materials recovery. Noise is small, idling noise value of about 20DB.
Use machine edge medium speed grinder use machine
 The middle-speed pulverizer is mainly used to place the plastic molding machine next to the robot with the nozzle material will be crushed into granular, and then by the immediate recovery device will be sent back to the plastic molding machine recycling again. Mostly used for machine edge crushing, compared with the strong crusher, slow crusher only for hard plastic crushing, and smashing power is relatively small, the cost is relatively high. Because such models are low speed, so the use of low noise generated. Unique turret design, high-quality tool (tool material Cr12MVo) preparation, so the powder particles evenly, less powder. The system to the product size optimization to the minimum, saving the site, and the bottom with a pulley, mobile and convenient. Widely used: this model crushing recovery PU, PET, PC, ABS and other soft and hard material outlet material. Easy to split design, color change material easy and easy, small and less space, suitable for small workshop machine room use.
Definition of Medium Speed Pulverizer
Use machine edge medium speed grinder use machine
The machine is used in the injection molding machine edge, crushing the injection molding machine in the injection process of plastic scrap, scrap, outlet material, semi-finished products and other materials, the crushed particles through the recovery system, mixed with the raw materials in proportion use. The machine side of the medium-speed crusher placed in the injection molding machine side smashing water and material recycling, greatly reducing the production costs, while the nozzle material, scrap recycling, to achieve environmental protection; if the re-configuration recovery device, with the manipulator operation, do not need Manual to operate, while saving labor costs.Use machine edge medium speed grinder use machine